BriskHeat® ACR-3-S120KIT ACR® 3 Hot Bonder Kit for Composite Heat Curing with SR Series Heater Blankets, Single-Zone, 100/130V

with SR Composite Heat Curing Blanket Heaters has an 8.4in (213mm) full-color HD touch-screen that allows easier and better composite curing with an easy-to-use interface. The single vacuum system has a built-in electric vacuum pump and vacuum venturi. It has 30 amps maximum output using universal voltage of 100-130VAC with a frequency of 50 to 60Hz. It accepts Type-J thermocouple connectors with up to 10 thermocouple sensor inputs. The quick 3-step programming uses simple drop-down menus and stores up to 30 programs that can be password protected. The USB port and USB flash disk allow for instantaneous data transfer and analysis using spreadsheet and word processor programs on PC. It is input ground fault interrupter breaker protected and has audible and visual alarms for high and low temperature/vacuum limits. Data logs either digitally or through a built-in printer that prints and records real-time status of cure including program parameters. It gives the user ability to manually adjust pressure and can cure up to 1400°F (760°C). Intended for use in dry environments (do not expose to spray) at altitude up to 6562ft (2000m). The storage temperature range is -4 to 140°F (-20 to 60°C) with an operating temperature range of 41 to 104°F (5 to 40°C). Pollution degree 2 (normally only non-conductive pollution occurs, however a temporary conductivity caused by condensation must be expected). This ACR® 3 Hot Bonder kit comes with SR Composite Heat Curing Blanket heaters with one 10 x 10in (254 x 254mm), one 12 x 12in (305 x 305mm) and one 16 x 16in (406 x 406mm). Kit also includes ACR® 3 Hot Bonder unit, two 10ft (3m) vacuum hoses, one 10ft (3m) input power cord, one 5ft (1.5m) heater output power cord, USB flash disk, 10 Type-J thermocouples, 10 standard connector adapters for thermocouple receptacles, 2 vacuum bag feed-throughs, 1 extra printer ribbon and paper and a DVD training video. Touch Screen Size: 8.4in (213mm). Input Voltage: Universal 100 To 130V. Frequency: 50 To 60Hz. Amperage: 30. Output Cord Receptacle: NEMA L14-30R. Pressure: 28in Hg (13.8PSI). Accuracy: ±3°F (1.67°C). Altitude: Up To 6562ft (2000m). Storage Temperature Range: -4 To 140°F (-20 To 60°C). Operating Temperature Range: 41 To 104°F (5 To 40°C). Maximum Relative Humidity: 80% For Temperatures Up To 88°F (31°C) Decreasing Linearly To 50% Relative To Humidity At 104°F (40°C). Number Of Zones: 1. BriskHeat #: ACR-3-S120KIT.

with SR Composite Heat Curing Blanket Heaters has an 8.4in (213mm) full-color HD touch-screen that allows easier and better composite curing with an easy-to-use interface. The single vacuum system has a built-in electric vacuum pump and vacuum venturi. It has 30 amps maximum output using universal voltage of 100-130VAC with a frequency of 50 to 60Hz. It accepts Type-J thermocouple connectors with up to 10 thermocouple sensor inputs. The quick 3-step programming uses simple drop-down menus and stores up to 30 programs that can be password protected. The USB port and USB flash disk allow for instantaneous data transfer and analysis using spreadsheet and word processor programs on PC. It is input ground fault interrupter breaker protected and has audible and visual alarms for high and low temperature/vacuum limits. Data logs either digitally or through a built-in printer that prints and records real-time status of cure including program parameters. It gives the user ability to manually adjust pressure and can cure up to 1400°F (760°C). Intended for use in dry environments (do not expose to spray) at altitude up to 6562ft (2000m). The storage temperature range is -4 to 140°F (-20 to 60°C) with an operating temperature range of 41 to 104°F (5 to 40°C). Pollution degree 2 (normally only non-conductive pollution occurs, however a temporary conductivity caused by condensation must be expected). This ACR® 3 Hot Bonder kit comes with SR Composite Heat Curing Blanket heaters with one 10 x 10in (254 x 254mm), one 12 x 12in (305 x 305mm) and one 16 x 16in (406 x 406mm). Kit also includes ACR® 3 Hot Bonder unit, two 10ft (3m) vacuum hoses, one 10ft (3m) input power cord, one 5ft (1.5m) heater output power cord, USB flash disk, 10 Type-J thermocouples, 10 standard connector adapters for thermocouple receptacles, 2 vacuum bag feed-throughs, 1 extra printer ribbon and paper and a DVD training video. Touch Screen Size: 8.4in (213mm). Input Voltage: Universal 100 To 130V. Frequency: 50 To 60Hz. Amperage: 30. Output Cord Receptacle: NEMA L14-30R. Pressure: 28in Hg (13.8PSI). Accuracy: ±3°F (1.67°C). Altitude: Up To 6562ft (2000m). Storage Temperature Range: -4 To 140°F (-20 To 60°C). Operating Temperature Range: 41 To 104°F (5 To 40°C). Maximum Relative Humidity: 80% For Temperatures Up To 88°F (31°C) Decreasing Linearly To 50% Relative To Humidity At 104°F (40°C). Number Of Zones: 1. BriskHeat #: ACR-3-S120KIT.